DVI-OPT-TX220-Pro
DVI Multimode Fiber Optical Extender
Designed for rental and fixed use, DVI‑OPT-220‑Pro series extenders can transmit DVI‑D signals over multimode fiber cables up to a range of 2500 m.
Designed for rental and fixed use, DVI-OPT-220-Pro series extenders can transmit DVI-D signals over multimode fiber cables for up to a range of 2500 m. Using Single Fiber Technology, the DVI-D signal is transmitted over one multimode 50/125 fiber core. Sources and display devices are galvanically isolated against ground loops and hum effects, and no delay occurs in the signal. The video image is transported without any frame latency. The Neutrik OpticalCON or ST fiber connectors ensure reliable operation in professional environments. The OpticalCON connectors are rugged, dust proof and very reliable, compatible with standard LC connectors.
Cross compatibility between Lightware fiber products is ensured, it is possible to connect these extender boxes directly to the MX modular matrix router using an MX-DVI-OPT series input or output board.
Applications
- Multiroom video and audio control
- Professional AV systems, conference rooms
- Rental and Staging
- Digital signage
- Long distance lossless DVI signal transmission
Compatible Fiber Cable
- Neutrik OpticalCON version: Neutrik 2M-4S75 hybrid, Neutrik 2M, LC-LC Multimode cable
- No signal latency, zero frame delay
- Extends DVI signals over one multimode fiber cable
- Dual outputs (two identical DVI outputs on the receiver)
- Single Fiber Technology
- Dual output with built-in distribution amplifier
- Extension distance up to 2500 meters (with OM3 fiber, 1920x1080p60)
- Cross compatible with OPT series Lightware fiber extenders and I/O boards
- Alarm output port
- Advanced EDID Management
- Advanced EDID Management (50 Factory presets, 50 user programmable slots)
- Advanced EDID Management in transmitter
- Pixel Accurate Reclocking
- Uncompressed video up to 6.75 Gbps datarate (225 MHz pixel clock)
- Firmware upgrade through serial port
- Device control via RS-232
- No video compression
- Status LEDs (source, monitor and laser detect)
- Local monitor output on transmitter
- Remote power available for receiver (using Neutrik 2M-4S75 hybrid fiber cable)
- Built-in universal power supply
- Breakout LC connector for Neutrik OpticalCON Duo unused fiber channel
- Improved ESD protection
- Mounting options for rack, furniture or truss
- Metal enclosure
| Connectors | |
| Power: | IEC connector |
| DVI: | 29 pole DVI-I connectors (only digital pins are connected) |
| Fiber: | Neutrik NO2-4FDW type LC duplex, LC simplex for B channel breakout |
| RS-232: | 9 pole standard D-SUB female |
| Specifications | |
| Data rate: | 1.65 Gbps per color |
| Resolution: | 640x480 to 1920x1200 |
| Video Delay: | 0 frames |
| HDCP pass through: | no |
| EDID emulation: | yes, Advanced EDID Management |
| EDID memory: | 50 factory preset, 50 user programmable EDID in transmitter |
| EDID support: | 256 byte Extended EDID v1.3 |
| Front panel control: | EDID management in transmitter |
| LED indicators: | power, source connected, signal present, laser active |
| RS-232 pass through: | no |
| Fiber: | 50/125 Multimode fiber |
| Laser: | 850 nm |
| Transmitter output OMA*: | -6.25 dBm (worst case) |
| Receiver OMA* sensitivity: | -14.25 dBm (worst case) |
| Optical loss budget: | 8 dBm (worst case) |
| Transmission distance (using OM3e type fiber): | 2500 meters |
| Remote power distance: | 600 meters |
| Power supply: | Internal (100 to 240 V AC, 50/60 Hz) |
| Power consumption: | 3.5 W |
| Enclosure: | 1U half rack, 1 mm metal |
| Dimensions: | 221W x 181D x 42.2 H mm |
| Net weight: | 1420 gramms |
| Compliance: | CE |
| Warranty: | 3 years |
| OMA*:Optical Modulation Amplitude | |
| Maximum extension distances | ||||
| OM1 | OM2 | OM3 | OM4 | |
| (62.5/125) | (50/125) | (50/125) | (50/125) | |
| 1080p@60Hz 24 bpp | Not supported | 600 m | 1200 m | 2500 m |